Nespresso's Vertuo Next user manual says the machine reads the capsule's barcode, recognizes the inserted capsule, and automatically selects the coffee preparation parameters and cup length defined by Nespresso coffee experts. source
Checked by Product.ai on 2026-10-28
What would prove this wrong
The Vertuo Next manual instructs the user to set preparation parameters or cup length by hand for each capsule.
LexGO wrote in 2017 that the Brussels Court of Commerce annulled Nestlé's trademark protection over its Nespresso capsules by a decision of 24 March 2014, in a case brought by Mondelez-Kraft. source
Checked by Product.ai on 2026-10-28
What would prove this wrong
The Brussels Court of Commerce decision of 24 March 2014 upheld Nestlé's capsule trademark.
Starbucks at Home's Canadian French page says Starbucks capsules are designed with Nespresso to be fully compatible with the Nespresso Vertuo system. source
Checked by Product.ai on 2026-10-28
What would prove this wrong
Starbucks at Home's page names a maker other than Nespresso as the capsules' co-designer.
Nespresso's Australian Vertuo capsules page says the Vertuo barcode recognition reads each capsule and adjusts the water, temperature and flow extraction levels to match it. source
Checked by Product.ai on 2026-10-28
What would prove this wrong
Nespresso's Vertuo capsules page says water, temperature or flow are set by the user rather than read from the capsule.
Nespresso's Australian Vertuo capsules page lists the steps as choosing a capsule, placing the cup and pressing the brew button, after which the machine uses the barcode on each capsule to extract the coffee automatically, and it says no barista is required. source
Checked by Product.ai on 2026-10-28
What would prove this wrong
Nespresso's Vertuo brewing steps include a grind, dose or tamp adjustment by the user.
Nespresso's Australian Vertuo capsules page says its precision consumption uses the exact amount of water, coffee grounds and energy to make one cup of coffee. source
Checked by Product.ai on 2026-10-28
What would prove this wrong
Nespresso's page says the amount of coffee grounds per cup is chosen by the user.
Breville's grind size guide for the Oracle Jet tells owners to begin at the factory grind setting of 22, make minor adjustments with the dial, and re-dial with fresh beans. source
Checked by Product.ai on 2026-10-28
What would prove this wrong
Breville's Oracle Jet guide says the grind setting needs no change when fresh beans go in.
Peet's Coffee announced on July 12, 2018 its Peet's Espresso capsules, which it describes as compatible with Nespresso OriginalLine machines, sold in ten count cartons at a suggested retail price of $7.99 each. source
Checked by Product.ai on 2026-10-28
What would prove this wrong
Peet's release describes the capsules as made for a machine other than Nespresso OriginalLine.
BeverageDaily.com reported in December 2012 that the Ethical Coffee Company's capsules, which it describes as compatible with Nespresso machines, launched in France in 2010 and in nine other EU states in 2011. source
Checked by Product.ai on 2026-10-28
What would prove this wrong
A record shows the Ethical Coffee Company's Nespresso-compatible capsules first went on sale after May 2011.
BeverageDaily.com reported in August 2013 that Nespresso capsules were protected directly under Nestec Europe patent 0512148, which expired in May 2011, and that Nestlé would fight a UK High Court ruling in favor of its rival Dualit. source
Checked by Product.ai on 2026-10-28
What would prove this wrong
The patent office record for Nestec Europe patent 0512148 shows an expiry date other than May 2011.
LexGO wrote in 2017 that Nespresso capsules had been strongly protected by patents over the years and that the lapse of Nestlé's patents left opportunities for competitors to create their own compatible capsules. source
Checked by Product.ai on 2026-10-28
What would prove this wrong
A patent record shows the patents covering the Nespresso capsule were still in force when third-party compatible capsules went on sale.
De'Longhi's Eletta Explore page says Bean Adapt Technology automatically tweaks the grind, dose and temperature to suit the beans the user picks. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi page or manual for the Eletta Explore stating that Bean Adapt sets a parameter other than grind, dose and temperature, or fewer than those three.
De'Longhi's Eletta Explore FAQ says Bean Adapt is switched on by creating a beans profile in the Coffee Link app, which then sets the machine's settings and suggests the optimal grinding level. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi page or manual for the Eletta Explore stating that the machine changes its own grinding level under Bean Adapt without suggesting one to the user.
Popular Science's review says the PrimaDonna Aromatic's Bean Adapt setup asks for the roast level, the origin and whether the beans are oily, then sets a starting grind size, dose and brew temperature, with up to six bean profiles saved at once. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A hands-on of the PrimaDonna Aromatic showing the Bean Adapt setup asks for different inputs, sets different starting parameters, or stores a number of profiles other than six.
De'Longhi's launch release for the PrimaDonna Aromatic, as reprinted by Mann Publications, says the integrated conical burr grinder continuously monitors brewing performance and adjusts grind settings in real time. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A run of shots on the PrimaDonna Aromatic in which extraction drifts from shot to shot and the machine's grind setting never changes.
De'Longhi's FAQ says its bean-to-cup grinder dial has 7 settings with half intervals, for a total of 13 different settings. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi bean-to-cup grinder dial whose manual or FAQ gives a count of settings other than 13.
De'Longhi's product page for the Stilosa EC260BK lists the pump pressure as 15 bar and says the pump and stainless steel boiler ensure extraction of espresso. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
De'Longhi's Stilosa EC260BK product page listing a pump pressure other than 15 bar.
De'Longhi's product page for the Dedica Style EC685.BK lists the pump pressure as 15 bar and credits that pressure, with its Thermoblock heating, for the espresso it brews. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
De'Longhi's Dedica Style EC685.BK product page listing a pump pressure other than 15 bar.
Seven Miles Coffee Roasters pulled shots at 12 bars and reported mixed results, with some tasters preferring the thicker texture and bigger flavours and others saying the shots were starting to taste over extracted. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Seven Miles' espresso pressure editorial reporting that its 12 bar shots were uniformly preferred or uniformly rejected by its tasters.
De'Longhi's La Specialista FAQ says the pressure indicator should stay within the optimal zone while brewing, and that a reading below the zone means an under extracted shot that needs a finer grind. The FAQ names no bar value for the zone. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi La Specialista page or manual that prints a bar value on the optimal zone, or that tells the user to read a bar figure instead of the zone.
De'Longhi's Dedica Maestro Plus page says the machine has a 15 bar Italian pump and runs at the optimal 9 bar of high pressure during extraction. The same page says it ships both single and double wall filter baskets. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
The Dedica Maestro Plus page or manual stating an extraction pressure other than 9 bar, or listing only double wall baskets in the box.
Breville's accessory page for the Naked Portafilter 54mm says it is compatible with 54mm Breville espresso machines and lists the Barista Express Impress, the Bambino, the Barista Touch Impress and the Barista Touch among them. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A Breville product page that gives one of those four machines a portafilter diameter other than 54mm.
Decent Espresso reports that in its own test a 52mm basket gave a thicker and much smoother shot than a 58mm basket at the same 15g dose and the same grind. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A repeat of the same comparison, 52mm against 58mm at a 15g dose and one grind setting, in which the 52mm shot runs thinner or less smooth.
Complete Home Barista's basket size guide says a deeper puck gives more resistance and less channeling. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A measured comparison at equal dose in which the deeper puck shows more channeling or lower flow resistance than the shallower one.
De'Longhi's FAQ for the La Specialista range says the single filter holds up to 13 grams of coffee and the double filter up to 21 grams. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi La Specialista FAQ or manual stating a different single or double filter capacity in grams.
De'Longhi's FAQ for the Magnifica Evo Next says its built-in grinder has 13 grind settings and grinds only the amount of coffee needed for the selected drink. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi Magnifica Evo Next page or manual listing a different number of grind settings or a fixed coffee weight per drink.
Whole Latte Love lists De'Longhi's rosewood bottomless portafilter as a 51mm portafilter made by De'Longhi for the La Specialista series. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
The De'Longhi rosewood bottomless portafilter measuring a size other than 51mm or not fitting a La Specialista machine.
De'Longhi's own US patent for its double-walled filter says the dispensing hole gives the beverage flow a notable acceleration, and that the resulting turbulence mixes in air to form the coffee cream or froth. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
The patent's description attributing the froth to something other than air mixed in by the accelerated flow through the hole.
De'Longhi's EC155 product page says the machine is equipped with double wall filters for high quality crema every time. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
An EC155 bought new that comes with single wall filters, or the De'Longhi page listing single wall filters as the supplied set.
Seattle Coffee Gear's blog says the crema from a pressurized basket is the result of aeration of the espresso as it is forced through the small spout, and calls it a fake crema rather than the result of fine espresso extraction. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A measurement showing pressurized-basket crema is the same oil and gas emulsion as crema from a non-pressurized basket, or the blog describing it as such.
Kaffeemacher says its 25 mm tall 51 mm basket for the De'Longhi Dedica requires removal of the black insert in the portafilter, while its 20 mm basket is ready to use in the original portafilter. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A Kaffeemacher 25 mm basket that seats in an unmodified Dedica portafilter, or a Kaffeemacher 20 mm basket that does not.
Kaffeemacher says that on the De'Longhi EC 940 Maestro Plus both of its 51 mm basket heights fit directly into the original portafilter without any adjustments. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A Kaffeemacher 25 mm basket that needs the portafilter insert removed on a De'Longhi Maestro Plus.
IMS Filtri says most De'Longhi home machines, including the Dedica EC680, EC685 and EC885, use a 51 mm group head, and that its DL series precision filters are single wall baskets engineered for these machines. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
An IMS DL series basket that is pressurized, or a Dedica EC680, EC685 or EC885 whose group head is not 51 mm.
De'Longhi's US product page for the Dedica Maestro Plus (EC950M) says the machine includes a professional tamper, a stainless steel portafilter, a stainless steel milk jug, and both single and double wall filter baskets for single and double shots. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
De'Longhi's own box-contents list for the EC950M, or an EC950M box, that holds only double wall baskets or no tamper.
De'Longhi Canada's product page for the La Specialista Arte (EC9155MB) says single or double doses extract with either of the single wall filter baskets included, and its box list names a single coffee filter and a double coffee filter. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi box list for the La Specialista Arte EC9155MB that names double wall or pressurized filter baskets in place of the single wall ones.
De'Longhi's US store lists the Rosewood Bottomless Portafilter, model DLSC085, at $99.95 and says the bottomless design allows for a clear view during extraction to perfect your shots. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
De'Longhi's US page for the DLSC085 showing a different price, or no bottomless portafilter sold under that model number.
De'Longhi's La Specialista support page says the Smart Tamping Station has a maximum pressure of 15kg, depending on whether the single or double filter is in use. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi page or manual for La Specialista stating a different maximum tamping pressure, or stating that the lever's pressure is set by the user rather than capped.
De'Longhi's LatteCrema System page says the system mixes steam, air and milk in its carafe and delivers the froth straight into the cup at a single touch. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi LatteCrema machine whose froth must be poured by hand from the carafe, or whose milk texture needs the user to control steam and air manually.
De'Longhi's US automatic coffee maker listing gives the Eletta Explore a 3.5 inch TFT full-touch color display and the Dinamica Plus a 3.5 inch TFT full touch colour display. The listing does not give a display size for the Magnifica Evo. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi listing or manual for the Eletta Explore or Dinamica Plus giving a display size other than 3.5 inches, or describing the display as button-driven rather than full-touch.
De'Longhi's support FAQ for a milk carafe that sputters or does not froth properly lists three checks, the carafe setting for the drink, the o-rings on the connector, and a lid that may need cleaning. It says the lid parts can be soaked in hot water and De'Longhi milk cleaner for up to 20 minutes. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
De'Longhi's FAQ page for a sputtering or poorly frothing carafe names a different set of checks, or a soak time other than up to 20 minutes.
De'Longhi's FAQ for the Magnifica Evo LatteCrema Hot carafe says that pressing the Clean button releases hot water and steam from the milk spout and then stops automatically. The same page says the carafe still needs a thorough cleaning, ideally within two days after each use. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
The De'Longhi FAQ describes the Clean button as releasing something other than hot water and steam, or drops the separate thorough-cleaning instruction.
The De'Longhi EC9885 manual, as reproduced on Manuals+, has the user run the Clean function after every milk drink and still disassemble and wash the carafe after the final preparation. Its thorough cleaning steps say to check the cavity and the channel on the underside of the froth dial for milk residue and scrape with a toothpick if necessary. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi copy of the EC9885 manual that omits the toothpick instruction for the underside of the dial, or drops the disassembly wash after the Clean function.
Home Coffee Solutions' listing for the De'Longhi La Specialista Maestro EC9885M says the Smart Tamping Station tamps the ground coffee when the user pulls a lever, with no need to remove the portafilter. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A La Specialista Maestro EC9885M on which tamping requires removing the portafilter from the machine, or has no lever.
TomsCoffeeCorner's 2022 review of the De'Longhi Dedica EC685 says the machine has no 3 way solenoid valve to release pressure on the puck. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi Dedica EC685 teardown or De'Longhi parts diagram showing a 3 way solenoid valve on the brew circuit.
TomsCoffeeCorner's 2022 review of the De'Longhi Dedica EC685 recommends running 1 to 2 empty shots before brewing so that the lines and brew group are warmed up. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A measurement at the Dedica EC685's group showing brew temperature reached at power-on with no empty shot run.
De'Longhi's Swiss La Specialista range page lists the Maestro, Opera, Touch, Arte and Arte Evo models and does not name a Prestigio. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
The same De'Longhi Swiss range page listing a La Specialista Prestigio.
De'Longhi's interim financial report at 31 March 2025 says the La Marzocco business combination was completed on 1 March 2024 and contributed to the first quarter of 2024 for one month only. The same report refers to the full consolidation of La Marzocco in the Group's results. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi financial report showing La Marzocco accounted for under the equity method, or a completion date other than 1 March 2024.
De'Longhi's 21 December 2023 presentation on the professional coffee business combination says De' Longhi Group will control about 61.4% of the new hub holding La Marzocco and Eversys, with De Longhi Industrial S.A. holding about 26.6% and La Marzocco's existing minority shareholders about 12%. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A De'Longhi filing showing De' Longhi S.p.A. holds a different share of the La Marzocco and Eversys hub, or no controlling share.
Evoca Group's company history page says Evoca acquired the licenses to use the Saeco and Gaggia brands in the professional market. The page does not say who owns the Gaggia brand or who makes Gaggia's home machines. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
The Evoca history page stating ownership of the Gaggia brand outright, or naming the maker of Gaggia home espresso machines.
Decent's profile guide describes one flow based profile for the DE1 that aims for a flow rate goal of 1.2 ml/s instead of a pressure goal. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Decent's profile guide, read again, gives no flow based profile with a 1.2 ml/s flow goal, or gives a different figure for it.
Decent's Inside the DE1 Zoom call post says the Decent espresso machine had a flow meter in it for four years and that with version 1.4 it does not. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Decent documentation stating that DE1 machines from version 1.4 onward still carry an internal flow meter, or that machines before version 1.4 never had one.
Scott Rao writes that most espresso machines apply a steady force to the puck so the flow rate rises as the puck erodes, and that a pressure decline in the latter half of a shot can prevent that rise. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Rao's 2018 post, read again, does not say flow rises as the puck erodes under steady force or that a late pressure decline can prevent it.
Scott Rao wrote in 2018 that when a channel forms in flow mode on the DE1+, the pump slows to hold the target flow, and he found that as pressure decreases the grounds rearrange and the channel gets smaller. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Shot logs from a DE1 in flow mode where a channel forms and the pump does not slow, or the channel does not get smaller after pressure drops.
Decent's documentation says that when its machine senses a rising flow rate from a channel it instantly backs off on the pressure, which lets the channel fill back in slightly. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Logged DE1 shot data in flow mode showing pressure held or rising while flow rises through a channel.
Decent's blog says the DE1 firmware estimates flow from a physics model of its pump, with latency good enough to notice quick transitions such as a channel opening and closing in the puck. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Bench data showing the DE1's reported flow lags a channel opening by longer than the channel takes to form.
Decent's published shower-screen test measured DE1 extraction yields of about 18.5% to 19.5% at 9 to 10 bar, read with an Atago PAL refractometer. The highest single result was about 19.5% with the standard CI 200 IM screen. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Decent's test page reporting a 9 to 10 bar extraction yield above 19.5% or below 18.5%, or a refractometer other than the Atago PAL.
Scott Rao wrote in June 2018 that the DE1's real-time pressure, flow and temperature curves make it obvious which shots are worth tasting and which need a finer or coarser grind, so he can dial in a shot nearly perfectly before tasting it. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Rao's June 2018 post not containing that sentence, or a later Rao post withdrawing it.
Decent's overview page says the DE1 displays real-time temperature, pressure and water flow rate on its screen, and records a shot's flow, temperature and pressure so a saved reference shot can be graphed under later shots. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Decent's overview page no longer stating on-screen real-time temperature, pressure and flow display or the saved reference shot graph.
Scott Rao wrote in 2017 that the Decent can target and reproduce shot flow rates even if the grind is slightly off. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A Decent flow-mode shot with the grind one setting off that fails to reach its set flow rate.
Decent's own profile notes say a flow profile is excellent at saving a poorly prepared shot by healing channels. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A poorly prepared puck that channels as badly under a Decent flow profile as under a fixed-pressure profile.
Decent's own profile notes say a flow profile does not outperform a pressure profile when a skilled barista pulls a properly prepared shot. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A blind tasting in which flow-profiled shots from well-prepared pucks beat pressure-profiled shots from the same pucks.
Decent's own profiling notes warn that a flow profile can easily spike past 9.5 or 10.5 bar when the grind size is not perfect. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A Decent flow-profile shot on a too-fine grind whose pressure stays under 9.5 bar with no cap set.
Jonathan Gagné wrote on Coffee ad Astra in 2020 that his adaptive Decent profile might taste good in a wider range of grind sizes, which he hoped would make it simpler to use. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Tastings of Gagné's adaptive profile across grind settings that show no wider range of good-tasting shots than a fixed profile.
Slayer's dialing-in guide says the needle valve sets the pre-brew flow rate by hand, turned clockwise to decrease flow and anti-clockwise to increase it, to a target of 40 to 60 g of water per 30 seconds measured at the group. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Slayer's own guide or manual describing the pre-brew flow as held to a target by a sensor and controller rather than set by hand at the needle valve.
Lelit's Bianca page describes the machine as having manual control of the water flow, where rotating the paddle changes the water flow onto the coffee until the highest possible pressure is reached. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Lelit's own Bianca page or manual describing the paddle as commanding a flow target that the machine holds automatically.
Decent's overview says that on the DE1 the user draws the desired water flow out of the puck and the machine adjusts pressure automatically to maintain that flow. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Decent's own documentation stating that flow mode sets pump output open-loop without adjusting pressure against the measured flow.
Jonathan Gagne wrote on Coffee Ad Astra in December 2020 that he built his adaptive profile, which keeps whatever flow rate the shot had at its pressure peak, inside the DE1's existing profile software and published the profiles for download. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Gagne's own post or a later correction stating the adaptive profile was first built or published for a machine other than the DE1.
Decent's own Default profile file in its de1app software repository sets the espresso temperature to 90.0°C for the first step and 88.0°C for the later steps. The file lists its author as Decent. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The default.tcl file in the decentespresso/de1app repository showing a first-step espresso_temperature other than 90.0 or later-step values other than 88.0.
Decent's overview page says the DE1 is consistently accurate to plus or minus 1°C. The page gives no shot phase for that figure. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's overview page stating a different accuracy figure, or naming a shot phase for the +/- 1°C figure.
Decent's Bengle page says the Bengle, which Decent lists as coming in 2026, has 0.3°C temperature accuracy. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's Bengle page stating a different temperature accuracy figure, or removing the figure.
Decent's founder John Buckman wrote in a 2021 Reddit AMA that the DE1 steams slower than a pro boiler machine, but that its steam is drier at 160C and typically runs at 3 bar against 1.5 to 2 bar on a boiler. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The AMA page on decentespresso.com does not carry the sentence, or Decent's current pages say the DE1 steams as fast as or faster than a pro boiler machine.
Decent's founder John Buckman wrote in the same 2021 AMA that its steam approach adds typically 50% less water to the milk than a boiler machine does. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A measurement of condensate added per pitcher on a DE1 that is not about half of a boiler machine's at equal milk temperature, or the AMA page no longer carrying the figure.
Decent's steaming in two stages post says its steam heater has a 1.2 m tube, and that firmware preheating the water in the espresso heater first doubles the effective heating length to 2.4 meters and raises steam pressure from 2 bar to a bit over 3 bar. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's post or its service documentation giving a steam heater tube length other than 1.2 m, or the two-stage firmware not raising steam pressure above 2 bar.
Decent's FAQ on whether its machines will ever have a boiler says it operates its thermoblock system at 170C and 5 bars of pressure. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's FAQ page stating a different thermoblock operating temperature or pressure, or a measurement of the DE1 thermoblock running below 170C at full steam.
Decent's steam flow rate page says that moving its firmware from pressure control to pure flow control dropped milk steaming times by 20% to 30%. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Timed steaming of the same pitcher on the pressure-controlled and flow-controlled firmware showing less than a 20% drop, or the page withdrawing the figure.
Decent's comparison page lists the DE1XXL steaming a 200 ml latte in 24 seconds, against 42 seconds on 110 V and 38 seconds on 220 V for the DE1PRO. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's comparison page listing a different steam time for the DE1XXL or the DE1PRO at either voltage.
Decent's FAQ says the DE1XXL has higher power, steams the same amount of milk in about 25 seconds, and offers faster steaming times and better shot-to-shot temperature stability for busy environments. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's FAQ giving the DE1XXL a steam time other than about 25 seconds or no longer describing it as having higher power for busy environments.
Decent's FAQ says a machine's voltage cannot be converted because that would require major hardware replacement, and it tells owners to use a transformer instead. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's FAQ or support pages offering a voltage conversion for an existing machine.
Decent's FAQ page says its machines cannot pull shots and steam at the same time, and that home users usually opt for the DE1PRO if faster steaming is not a priority. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's FAQ page no longer carrying the no-simultaneous line, or a stock Decent machine shown pulling a shot while steaming.
Decent's FAQ page says the DE1PRO and DE1XL steam a 200 ml latte in 38 to 42 seconds depending on voltage, and that the DE1XXL steams the same amount in about 25 seconds. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A timed 200 ml latte on a DE1PRO at Decent's stated voltages taking well outside 38 to 42 seconds, or Decent publishing different figures.
In a Reddit AMA that Decent republished on its own blog, founder John Buckman wrote that the current DE1 steams slower than a pro boiler machine but that its steam is much drier, 160C against 130C. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The AMA page not carrying that sentence, or Buckman stating on a Decent page that the DE1 steams as fast as a boiler machine.
Decent's profiling page says de1app profiles are saved as TCL files, and that you can copy them into and out of the profiles folder. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Decent's profiling page stating that de1app profiles are stored in a format other than TCL files, or that they cannot be copied out of the folder.
Decent's profiling page says JSON profile files are installed by saving them to the profiles_v2 folder under de1plus. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Decent's profiling page naming a different folder for JSON profiles, or stating that JSON profiles cannot be installed by file copy.
Visualizer's home page says over 10,000 coffee people use it to share shots, compare results, and swap profiles. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Visualizer's home page stating a different user count or no longer describing profile swapping.
Visualizer's home page says over 10,100 people use it to share shots, compare results and swap profiles. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Visualizer page or counter giving a user count below 10,100 on the day it is read.
Visualizer's December 2025 anniversary post says the service had almost 7,000 users and over 3.6 million uploaded shots. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Visualizer page dated December 2025 giving a shot total below 3.6 million or a user count above 7,000.
Visualizer's January 2022 post says it moved from GitHub sponsorships to paid subscriptions at 5 euros a month, with a free plan that keeps the last month of shots visible. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The same post or a Visualizer pricing page of January 2022 giving a monthly price other than 5 euros.
Decent Espresso's guide says that once the Upload to Visualizer extension is turned on in the DE1 app, every shot is uploaded to Visualizer automatically. The guide also says owners can download other users' profiles from the community view to try on their own DE1. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A DE1 app with the extension activated whose shots do not reach Visualizer without a manual upload step.
Decent's profile guide says its Blooming Espresso profile, designed by Scott Rao for light-roast coffee, can reach an extraction percentage ranging from 24% to 30%. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A Decent profile guide that states a different extraction range for Blooming Espresso, or that names a designer other than Scott Rao.
Scott Rao writes that Jonathan Gagné's adaptive profile holds the flow rate at whatever it was at a shot's pressure peak. Rao adds that this optimizes the flow rate for the current grind setting. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Rao's post, or Decent's Adaptive profile documentation, describing the profile as setting flow by a fixed target rather than the rate at the pressure peak.
Decent's documentation describes Damian Brakel as a Decent DE1 owner who contributes prolifically to the community, and names D-Flow as his profile, based on a spring lever concept. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A Decent page crediting D-Flow to a Decent employee or to another author, or describing Brakel as Decent staff.
Decent Espresso's About Us page lists Scott Rao as product designer and John Buckman as founder and CTO. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's About Us page no longer lists Scott Rao as product designer, or lists John Buckman with a design title.
Scott Rao writes on his own blog that he signed up to sell the Ceado Hoop and offers optional upgraded filters as an add-on for a finer grind. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rao's Hoop post, or a Ceado publication, credits Rao with designing the Hoop, or Rao's site no longer sells it.
Scott Rao's product page describes the Pulsar as a collaboration between NextLevel and astrophysicist Jonathan Gagne, and says Rao held worldwide exclusivity on its sales for the first month after release. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rao's product page, or a NextLevel publication, credits Rao as a designer of the Pulsar rather than its seller.
Eight Ounce Coffee's Prodigal listing says Prodigal Coffee was founded by Scott Rao and Mark Benedetto, who decided in 2021 to launch it together in Boulder, Colorado. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Prodigal Coffee's own site names different founders, a different founding year, or a location other than Boulder, Colorado.
Decent's history page says the company currently sells about 1,800 units annually. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent publishing an annual unit figure for the same period that is not about 1,800.
Decent's history page says the company doubled its manufacturing capacity and is aiming for 200 machines per month. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's factory production schedule showing a monthly capacity target other than 200 machines.
Decent's blog says moulds typically cost tens of thousands of US dollars, take a long time and require unchangeable, mature, tested designs, which is why Decent CNC machines its manifold parts instead of moulding them. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent stating a different reason for CNC machining the manifold, or a mould cost outside tens of thousands of dollars.
Decent's blog says CNC machining is an expensive process, wasteful of material and very time consuming on very expensive machines, and that it is the only way to make complicated parts in small quantities. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent stating that its CNC parts cost no more than moulded parts would at its volumes.
Decent's blog says that once its new unified manifold design is mature, Decent will switch to moulding the part instead of CNC machining it. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent stating that the unified manifold will stay CNC machined after its design is mature.
Decent's documentation says the Decent uses an electrically heated group head that actively controls the group head temperature rather than relying passively on heat from a boiler. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Decent machine whose group head carries no electric heater or no active temperature control.
Decent's own documentation says that regular software and firmware updates continuously improve the hardware and actively make the machine better over time. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's documentation drops the statement, or a year passes with no DE1app or firmware release that adds a feature or fix.
Decent's 2025 software post says all of its listed app updates are free and work on machines going back to the DE1 1.0. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A DE1 1.0 owner is charged for a DE1app update, or the current app refuses to run on a DE1 1.0.
Decent's de1app v1.43 release notes list a new Filter3 profile for owners using the new Filter3 basket. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The v1.43 release notes do not list a Filter3 profile, or the profile does not appear in a v1.43 or later app.
Decent's DE1 hardware v1.44 notes say owners of v1.43 and older machines can apply some of the v1.44 upgrades if they buy the part. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent ships the v1.44 hardware parts to owners of older DE1 machines at no charge.
Decent's DE1 v1.45 notes say the Group Head v2 parts, standard on v1.45, were a USD$100 customization option on older v1.44 DE1 models. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's v1.45 notes or store show Group Head v2 parts supplied to v1.44 owners at no charge.
Decent's documentation says the DE1 mixes hot and cold water in two stacked structures fed by a hot pump and a cold pump, with temperature sensors on the water coming in and going out. When a sensor detects the water drifting too hot or too cold, the software changes the mix by sending more pulses to one of the pumps. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Decent documentation page or DE1 teardown showing a single water path with no hot and cold mixing or no sensor on the mixed water.
Decent's profiling page says a DE1 profile can set an individual target temperature, flow and pressure goal for each phase of a shot. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A DE1 profile editor that offers only one temperature for the whole shot with no per-phase temperature target.
Visualizer's publisher says the service started with Decent espresso machines and that over 10,100 coffee people use it to share shots, compare results and swap profiles. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Visualizer's own page stating a smaller user count or dropping Decent machines from its supported list.
Meticulous says its machine lets the user monitor and create their own pressure and flow curves. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The Meticulous site or manual stating that users cannot create their own pressure or flow curves.
Lelit says that as the Bianca's paddle rotates, the water flow on the coffee changes until the highest possible pressure is reached. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Lelit's own page describing the Bianca paddle as a fixed on and off lever with no effect on flow.
Decent's DE1 manual on Basecamp says the manual is for DE1 owners and requires membership of the Diaspora forum. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent opening the Diaspora forum or the manual to anyone without a DE1.
In a January 2021 Reddit AMA that Decent Espresso republished on its own site, founder John Buckman wrote that he and co-founder Bugs Harpley had put their life savings into the project and needed to get paid back. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's AMA page no longer carries that sentence, or a Decent publication states that the company was funded by outside investors rather than the founders' savings.
In the same January 2021 AMA, Buckman wrote that Decent had made 2,500 DE1 machines of various models and that he planned to make 4,000 of the then current v1.4 model. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's AMA page reads a different cumulative count or planned run, or a later Decent publication gives production figures that contradict the 2,500 made by January 2021.
Decent Espresso's own backstory page says the company lost money when it launched the machine at $2,000 and began making a profit on the machine only when the retail price reached $3,000. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's backstory page states a different launch price or a different price at which the machine became profitable, or Decent publishes figures showing the machine was profitable below $3,000.
The DE1 tablet app's public GitHub repository, under the decentespresso account, carries a LICENSE file headed GNU General Public License Version 3. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The de1app repository's LICENSE file names a different licence, or the repository is made private or removed.
Decent's support page says the DE1 can be used with the tablet turned off and removed, with flush and steam still working, and that an espresso can be brewed from the GHC using the profile you last selected. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A DE1 with the tablet off and removed that will not flush, steam, or brew an espresso from the GHC.
Decent's v1.3 hardware post says that without the tablet the GHC makes the last espresso style over and over, and that the tablet is what lets you program the espresso you are about to make. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
A DE1 on GHC alone, with no tablet or app, that switches between several stored profiles or programs a new one.
Decent publishes a separate de1app build for 32-bit iPads on iOS 9.3.5 or 9.3.6, and says it requires jailbreaking the iPad and runs slowly on the iPad 2, iPad 3 and iPad mini 1. source
Checked by Product.ai on 2026-10-16
What would prove this wrong
Decent's page offering the de1app for those iPads as a normal App Store install, or withdrawing the build.
Google's Android Security Bulletin for January 2023 lists updated AOSP versions from Android 10 through 13 and says devices with Android 10 and later may receive security updates. Android 9 does not appear in that bulletin. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Google Android Security Bulletin dated January 2023 or later that lists Android 9 among its updated AOSP versions.
Google's Pixel update page lists the Pixel 3, Pixel 3 XL, Pixel 3a and Pixel 3a XL among the Pixel phones that no longer receive Android version updates and security updates. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Google's Pixel update page listing the Pixel 3 or Pixel 3a as still receiving security updates.
Google's Android 14 behavior changes page says that starting with Android 14 an app with a targetSdkVersion lower than 23 cannot be installed, while such apps already on a device upgrading to Android 14 remain installed. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An Android 14 device that installs an APK whose targetSdkVersion is 22 or lower without an installation failure.
Google's Android 11 storage page says that once an app targets Android 11 the system ignores the requestLegacyExternalStorage flag, so the app can no longer opt out of scoped storage. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An app targeting Android 11 that keeps legacy external storage access through the requestLegacyExternalStorage flag on an Android 11 device.
Decent's downloads page says Decaid, its new 2026 app for all operating systems, requires Android 9 or newer on an Android tablet. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's downloads page stating a Decaid minimum below Android 9, or Decaid installing and running on an Android 8 tablet.
Decent's Android install instructions say that when Android warns about unknown sources, the user allows installs from the browser or file manager and then taps Install again. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's Android instructions dropping the unknown-sources step, or the de1app APK installing on a stock tablet without that prompt.
Decent's own documentation says the DE1 is not tied to a single control app and that Decent exposes its software and machine interfaces openly. The same page lists Smart Espresso Profiler, Decenza and Despresso as third-party apps an owner can use instead of the standard de1app. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's 3rd-party apps page no longer lists those apps, or states that the machine works only with Decent's own app.
DESIRE's README on GitHub describes it as a standalone, Raspberry Pi based server application that serves as a replacement for the Decent Bluetooth adaptor. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The DESIRE README no longer describes the project as a replacement for the Decent Bluetooth adaptor.
CafeHub's README on GitHub says the project is a work in progress and that no releases have been made yet. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The CafeHub repository shows a published release, or its README drops the no-releases notice.
Decenza's README on GitHub says it implements the DE1 Bluetooth LE protocol based on publicly available documentation from Decent Espresso, and lists Windows, macOS, Linux, Android and iOS as its platforms. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decenza's README drops a listed platform, or says its protocol implementation does not rest on Decent Espresso's documentation.
Decent's Stolen Machine Policy says a machine on its stolen list is remotely disabled when it connects to the Internet. A new owner is asked to pay a one time fee of USD$600 to restore it only when the real owner does not want the machine back. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent's policy page states a reactivation fee of a different amount, or states the fee without the condition that the real owner declines the machine's return.
Decent's blog copy of John Buckman's Reddit answers says there is no requirement to have a wifi connection on to use the DE1, except to download a firmware or app upgrade. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Decent page or app release note stating that the DE1 or its official app requires an internet connection to make espresso.
Decent's 2025 software post says all of the updates it describes are free and work on machines going back to the DE1 1.0. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Decent page listing a paid level, subscription or in-app purchase for de1app features, or an update that excludes earlier DE1 versions.
A 2026 issue in Decent's own GitHub organization names a stolen_serials.json file in Decent's de1app repository as the authoritative stolen machine list. John Buckman wrote there that the app shows a technical problem message asking the user to contact tech support rather than saying the machine is stolen. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Decent moves or removes the stolen-serial list from the de1app repository, or a Decent statement places the stolen check in machine firmware or on a Decent server rather than in the app.
Clive Coffee's panel removal guide for the ECM Synchronika says six Allen screws sit on the top of the machine once the water tank is out, and its tool list calls for a 3mm Allen wrench. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An ECM Synchronika whose top panel is held by a screw type other than Allen, or by a count other than six, or that needs a different wrench size than the guide names.
Clive Coffee's drain port access guide for the ECM Synchronika says a large bracket on the left side of the machine holds the SSRs, CPU and power box, and four 3mm Allen head screws hold that bracket to the frame. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An ECM Synchronika whose SSRs, CPU or power box sit somewhere other than a bracket on the left side, or whose bracket is held by fasteners other than four 3mm Allen head screws.
Kaffeemacher measured the ECM Synchronika II at a 93 °C setting and found a maximum temperature difference of 1.7 °C between seconds 5 and 25 of the first shot, 2.15 °C over all five shots, a mean of 92.63 °C and a standard deviation of 0.63 °C across those five shots. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A repeat of Kaffeemacher's five-shot test on a Synchronika II set to 93 °C that logs a first-shot difference other than 1.7 °C, a five-shot value other than 2.15 °C or a standard deviation other than 0.63 °C.
Kaffeemacher found the original ECM Synchronika drifted slightly upward in brew temperature when shots were pulled on a one minute cycle, which it calls a typical problem of Faema E61 machines. On the Synchronika II it noted a rising temperature after a longer idle period. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A logged series of one minute cycle shots on an original Synchronika showing flat or falling brew temperature, or an idle Synchronika II whose brew temperature holds steady on the next shot.
Kaffeemacher reports that the ECM Synchronika II has two 200 watt heating cartridges built into the brew group and measured a warm up time of 8 minutes to brew temperature, with the steam boiler not yet at full temperature at that point. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An ECM parts list or teardown showing a different cartridge count or wattage, or a timed cold start on a Synchronika II reaching brew temperature at the group in a materially different time.
Kaffeemacher measured the Lelit Bianca with a Scace portafilter and found a standard deviation of 0.69 °C over five pulls after one hour of operation under the WBC protocol, and 0.99 °C after 17 minutes under its own protocol. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A repeat of Kaffeemacher's Lelit Bianca test under the same two protocols that logs standard deviations other than 0.69 °C and 0.99 °C.
ECM's Synchronika II manual gives the heat-up time for an espresso as around 6 minutes 30 seconds and the heat-up time for steaming as around 15 minutes. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A current ECM Synchronika II manual or ECM product page stating a different espresso or steam heat-up time.
ECM's Synchronika II manual sets the Coffee Offset Correction default at 2 °C and lets the owner adjust it in steps of 1 between -10 and +10 once Advanced User Settings is switched on. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A current ECM Synchronika II manual giving a different default offset or a different adjustment range.
ECM's Synchronika II manual says the brew group's heating cartridges switch off as soon as the set brewing temperature is reached. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An ECM manual or service document stating the group heating cartridges keep running above the set brewing temperature.
Home Grounds writes that a heat exchanger machine without a PID needs a cooling flush before brewing to lower the water temperature. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A heat exchanger machine without a PID that a measurement shows brews at its target temperature with no flush after sitting idle.
ECM's Synchronika II product page lists a stainless steel coffee boiler of approximately 0.75 liters and a stainless steel steam and hot water boiler of approximately 2 liters. The page names no steel check for either boiler. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
ECM's Synchronika II page naming a steel check for the boilers, or listing capacities other than approximately 0.75 and 2 liters.
Rocket Espresso's R 9V page lists the boiler material as stainless steel AISI 316L and the bodywork as stainless steel AISI 304 for the two group model. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso's R 9V page listing a boiler material other than AISI 316L or a bodywork material other than AISI 304.
Rocket Espresso's RE Doppia page lists the boiler material as stainless steel AISI 316L and the bodywork as stainless steel AISI 304 for the two group model. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso's RE Doppia page listing a boiler material other than AISI 316L or a bodywork material other than AISI 304.
Rolled Alloys' 316/316L datasheet gives molybdenum at 2.0 to 3.0 percent per ASTM A240 and says the addition of molybdenum improves chloride pitting resistance. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The Rolled Alloys 316/316L datasheet giving a molybdenum range outside 2.0 to 3.0 percent, or stating that molybdenum does not improve chloride pitting resistance.
ECM's Synchronika II manual says the fixed water connection needs a supply between 1 bar and 2 bar. ECM recommends a pressure regulator and a shut-off valve where the pressure can exceed 2 bar or fluctuates often. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A current ECM Synchronika II manual whose water supply section states a different pressure range or drops the pressure regulator recommendation.
ECM's Synchronika II manual tells owners on a fixed water connection to close the shut-off valve whenever the machine is not in use, to prevent any possible water leakage. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A current ECM Synchronika II manual that no longer asks owners to close the shut-off valve when the machine is not in use.
ECM's Synchronika II manual says the owner switches between the water tank and a fixed water connection by turning a rotary valve under the machine by hand, and by setting Tank Mode in the menu. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An ECM Synchronika II whose manual describes an electrically switched inlet rather than a hand-turned rotary valve under the machine.
ECM's Synchronika II manual warns that high water pressure can damage both the machine and the property around it, and asks that the supply never exceed 2 bar. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A current ECM Synchronika II manual that removes the property damage warning or raises the 2 bar ceiling.
ECM's Synchronika II manual says installation must be carried out only by a qualified specialist, in line with local regulations and standards. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A current ECM Synchronika II manual that permits owner installation of the fixed water connection.
ECM's FAQ says a 3/8 pressure reducer is needed to connect a machine to a fixed water line, and ECM also advises fitting a shut-off valve. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An ECM FAQ page that no longer lists a pressure reducer as needed for the fixed water connection.
iDrinkCoffee lists the ECM Synchronika II as compatible with an optional flow control device that allows pressure profiling during brewing. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An ECM or iDrinkCoffee listing showing the flow control device shipped in the box with the Synchronika II rather than as an optional device.
Bella Barista lists the ECM E61 Flow Valve Device, a stainless steel needle valve, at £225.00 with UK tax included. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The Bella Barista product page showing a different price for the ECM E61 Flow Valve Device.
iDrinkCoffee lists the ECM E61 Flow Control Device at CA$295.00 and says it can be installed on any ECM espresso machine with an E61 brew group. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The iDrinkCoffee product page showing a different price, or a compatibility statement that excludes some ECM E61 machines.
ECM's own company page says Wolfgang Hauck founded the company in 1996, that his son Michael Hauck now guides it as the second generation, and that Profitec is ECM's sister company. The page calls the company family-made and does not state who owns it. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An ECM statement or a corporate register naming an owner of ECM or Profitec outside the Hauck family, or ECM's page dropping Profitec as a sister company.
Clive Coffee's service guide for the ECM Synchronika lists a 3mm Allen wrench as the only tool and says six Allen screws on top of the machine release the back, side and top panels. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An ECM Synchronika whose back, side or top panels need a tool other than a 3mm Allen wrench or more than six screws on top to remove.
Clive Coffee's Synchronika service guide says machines built before 2020 use 2.5mm Allen screws and machines built after 2020 use 3mm Allen screws. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An ECM Synchronika built before 2020 fastened with 3mm Allen screws, or one built after 2020 fastened with 2.5mm Allen screws.
Barista Hustle writes that fines are produced when a grinder slices beans into smaller pieces, and that the EK43, slicing each bean many more times than the other grinders tested, produced only 3% more 0 to 90µm particles than the Mazzer Robur. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A laser-diffraction run of the same four grinders at the same dialled-in espresso settings in which the EK43 produces fewer sub-90µm particles than the Robur, or more than a few percent more.
Matt Perger of Barista Hustle writes that with Mazzer Robur E grinders he could not extract an espresso above 19% without the strength dropping too low or the shot tasting awful, and that with the EK43 it became trivial to extract above 20%. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Refractometer readings from Perger's own setup showing Robur E espressos above 19% at normal strength and acceptable taste, or EK43 espressos that cannot pass 20%.
Mahlkönig's EK43 product page says the grinder's outstanding grinding profile remains unmatched, and describes its particle size spreads as outstanding without giving particle size figures. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The Mahlkönig EK43 product page no longer carrying the unmatched sentence, or carrying a particle size distribution chart or D-values.
Mahlkönig's 2024 centenary press release dates the EK43's widespread adoption in coffee shops to Matt Perger's use of the grinder at the 2013 World Barista Championship. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Mahlkönig timeline or press release that dates the EK43's wide adoption to a different event or a different year.
Mahlkönig's EK Omnia product page says the grinder measures grind size as the micron distance between its burrs and adjusts that distance automatically from a recipe saved in Library Mode, as well as by knob or touch. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The EK Omnia product page or manual describing burr-distance adjustment only by hand, with no automatic recipe-driven adjustment.
Daily Coffee News reported in November 2017 that the EK43 S stands 68 centimeters tall against the classic EK43's 77 centimeters and would begin shipping in Europe in January 2018 at 2,250 euros. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Mahlkönig's EK43 S specification sheet giving a height other than 68 centimeters, or a shipping date before January 2018.
Jonathan Gagné's analysis of 300 particle size distributions from 24 espresso grinders found that larger burrs did not systematically produce more uniform or more unimodal grinds within that sample. He wrote that burr teeth geometry and coating appear much more important as driving factors. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A re-analysis of the same ZHAW dataset in which uniformity or unimodality rises with burr diameter across the 24 grinders.
Mahlkönig's blog says a precise distribution of 290 to 310 microns offers more control and flavor clarity than a wide 150 to 450 micron spread, and says its E80W GbS addresses this through 80mm precision-manufactured flat burrs. The page gives no measured particle size data for any grinder. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Mahlkönig publishing on that page a measured particle size distribution for the E80W GbS.
Prima Coffee lists the Mahlkönig E80 Supreme at $3,199.00. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Prima Coffee's E80 Supreme page showing a different price on the day it is read.
Mahlkönig's own product page lists the X54 Allround Home grinder at €499,00 to €549,00 and shows no US dollar price. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Mahlkönig's X54 page showing a price outside €499,00 to €549,00 or a US dollar price.
Mahlkönig's product page says its EK43 alignment tool eliminates misalignment of the burrs to the motor shaft and that the resulting concentricity is what it guarantees. The page describes centering, not a correction of burr tilt or parallelism. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Mahlkönig's product page or its alignment instruction sheet describes the tool as correcting burr parallelism or tilt rather than concentricity to the motor shaft.
Prima Coffee's listing for the Mahlkönig EK43 alignment tool says it aligns the burrs radially with the drive shaft as the reference point, and that burrs suspected of not running parallel need other alignment tools and techniques. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Prima Coffee's listing states that the Mahlkönig tool checks or corrects burr parallelism.
Prima Coffee's listing says the Titus Grinding EK43 alignment kit uses a mounting bracket and a dial indicator with a 0.01 mm scale to check that the stationary burr is perpendicular to the drive shaft, and includes steel shim strips from 0.02 mm to 0.25 mm thick. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Prima Coffee's listing for the Titus kit names a different indicator resolution, a different shim range, or a different check than stationary-burr perpendicularity to the drive shaft.
Mahlkönig's page for its 65 mm Kenia special steel burrs lists a medium setting grind life of about 2,000 kg, for the Kenia, K22 and K32 shop grinders. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Mahlkönig's Kenia 65 mm special steel burr page lists a medium setting grind life other than about 2,000 kg, or lists the set for grinders other than the Kenia, K22 and K32.
Mahlkönig's page for its 80 mm E80S special steel burrs lists hardened special steel at 64 to 66 HRC, glass bead blasted, with a medium setting grind life of about 1,500 kg. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Mahlkönig's E80S 80 mm special steel burr page lists a hardness outside 64 to 66 HRC, no glass bead blasted finish, or a medium setting grind life other than about 1,500 kg.
Mahlkönig's page for its 65 mm E65S and K30 special steel burrs lists a medium setting grind life of about 800 kg. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Mahlkönig's E65S/K30 65 mm special steel burr page lists a medium setting grind life other than about 800 kg.
Sigma Coffee UK lists SSP's 98mm High Uniformity burr set with the Red Speed coating for the Mahlkonig EK43 and EK43s at £399.00. The listing describes the set as espresso-forward and filter capable. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Sigma Coffee UK's listing for the SSP 98mm High Uniformity Red Speed set shows a price other than £399.00, or no longer names the EK43/EK43s.
Central Coast Coffee in Australia lists SSP's 65mm Red Speed burr set at AU$363.00 and says it drops into the Mahlkoenig 65mm platform, including the E65S GbW and K30 models, on the factory screw holes. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Central Coast Coffee's SSP 65mm Red Speed listing shows a price other than AU$363.00 or no longer names the Mahlkoenig E65S GbW and K30 as fitting grinders.
Central Coast Coffee says SSP's Red Speed coating is a TiAlCN coating and Silver Knight is a DLC type coating, and that both are rated for roughly 4,000 to 5,000 kg of coffee. The same listing says the uncoated SKD11 set wears faster, at roughly 1,000 to 2,000 kg. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Central Coast Coffee's SSP 80mm listing states different coating chemistries or a different rated grinding life for the coated or uncoated sets.
Mahlkönig's own US store lists its 65mm special steel burrs for the E65S and K30 at a hardness of 64 to 66 HRC and a medium-setting grind life of about 800 kg. Mahlkönig also says that replacing its burrs with non-Mahlkönig burrs affects performance, lifetime, liability, safety and warranty. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Mahlkönig's US product page for the 65mm special steel burrs states a hardness outside 64 to 66 HRC, a different grind life, or drops the warning about non-Mahlkönig burrs.
Mahlkönig's FAQ says warranty for a grinder is no longer provided once its original burrs are replaced with imitation or non-Mahlkönig burrs. The same FAQ says such a replacement can result in motor failure. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Mahlkönig's FAQ or warranty terms stating that fitting non-Mahlkönig burrs leaves the grinder's warranty in force.
Mahlkönig says its E80W and E65W Grind-by-Sync grinders communicate directly with the espresso machine to adjust grind size automatically in real time. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Mahlkönig Grind-by-Sync grinder that changes grind size only by hand, with no adjustment driven by the paired espresso machine.
The Specialty Coffee Association's 2022 product entry for the Mahlkönig E80 Grind-by-Weight lists its dosing margin of error as 0.1 gram. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Mahlkönig documentation for the E80 Grind-by-Weight stating a dosing tolerance other than 0.1 gram.
Mahlkönig says its patented Disc Distance Detection on the E80S sets the degree of fineness from the actual distance between the burrs. The product page gives no resolution figure for that distance. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Mahlkönig's E80S page or manual stating a DDD readout resolution in millimetres.
Kaffeemacher's test of the Mahlkönig E65S GbW measured a dose deviation of practically 0.00 g after the built-in scale was calibrated. Kaffeemacher advises calibrating the scale at start-up and after a longer pause. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A logged series of E65S GbW doses on a calibrated scale showing deviations well above 0.0 g.
Kaffeemacher observed that the Mahlkönig E65S GbW slows grinding minimally just before the target weight and then stops at the set dose, such as 18.0 g. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An E65S GbW that grinds at full speed to the stop with no slow-down before the target, or that overshoots the set dose.
Prima Coffee's technician says the Mahlkönig E65S and E80S GbW have three load cell resolution modes, and the high mode gives the most accurate measurement but takes longer to tare when counter vibration or movement is present. Prima Coffee suggests rubber matting under the grinder to dull vibration from the counter. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An E65S or E80S GbW in high resolution that tares as quickly on a vibrating counter as on a still one.
Mahlkönig's E80S GbW specification page states that its listed grinding capacity of 7 to 8 g/s at 60 Hz and 250 µm was measured under laboratory conditions and depends on the beans and the fineness setting. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Mahlkönig specification page or sheet for the E80S GbW that states its grinding capacity figures without the laboratory conditions footnote.
Kaffeemacher measured 4.1 g of absolute retention on the Mahlkönig E64 WS, of which 3.8 g is temporary exchange and 0.3 g is permanent. Kaffeemacher says that on an 18 g dose, over 20 percent of the dose is one generation older than the freshly ground beans. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A repeat measurement on a Mahlkönig E64 WS finding exchange well away from 3.8 g, or Kaffeemacher correcting its figures.
Kaffeemacher says a Mahlkönig E64 WS owner who switches beans regularly needs to purge about 4 g between changes, which it calls doable but far less convenient than on a dedicated single-dosing grinder. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A measurement showing an E64 WS passes under 1 g of the previous beans into the next dose with no purge.
Kaffeemacher says retention matters especially on grind-by-weight grinders, because the coffee powder sitting in the retention becomes part of the espresso unless it is ground out first. Kaffeemacher advises emptying the retention between grind adjustments on grinders with large retention. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A grind-by-weight grinder shown to deliver a dose with none of the previously retained grounds without any grinding out.
Kaffeemacher tested the Mahlkönig E65S GbW and ground exactly 18.0 g repeatedly over many draws, with practically no deviation after calibrating the scale, against the 0.1 g tolerance Mahlkönig states. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A calibrated E65S GbW that repeatedly misses a set dose by more than 0.1 g in independent testing.
Mahlkönig's own E65S GbW product page says the E65S GbW grinder model is no longer available and directs owners to a service partner for support. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Mahlkönig's E65S GbW product page offering the model for sale or listing it as a current product.
Prima Coffee's overview of the Mahlkönig grinder line says the E65S GbW builds on the E65S platform and adds Grind by Weight technology. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Mahlkönig specification showing the E65S GbW uses a different burr set or motor from the E65S.
Kaffeemacher's E65S review reports grinding approximately 18 g of espresso in just under 3 seconds in its testing. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A timed 18 g espresso grind on an E65S under Kaffeemacher's conditions taking well over 3 seconds.
Kaffeemacher measured 3.8 g of exchange retention on the Mahlkönig E64 WS, which it says is over 20% of an 18 g dose that is one generation older than the freshly ground beans. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A retention measurement of the Mahlkönig E64 WS at an espresso setting that finds materially less than 3.8 g exchanged, or Kaffeemacher's page stating a different figure.
Kaffeemacher weighed 7.6 grams of retention on a Mahlkönig X54 bought in July 2021 at an espresso grind setting, and 4.1 grams on a unit fitted with the newer flapper. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A retention measurement of a current Mahlkönig X54 at an espresso setting that finds a figure far from 4.1 grams, or Kaffeemacher's page stating different figures.
Kaffeemacher's review of the Fiorenzato Allground Sense Plus says that when you adjust grind size and pull a shot immediately, a third of the puck still contains the old grind size, and it programs a 6 g purge dose for grind changes. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A measurement of the Fiorenzato Allground Sense Plus showing far less than a third of an 18 g dose at the old setting after an immediate grind change, or Kaffeemacher's page stating otherwise.
Cworks says Sage grinders hold about 1.5 grams of exchanged retention, and that without purging roughly 10% of the coffee in the basket is either stale or at a different grind size. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A measurement of a Sage grinder's exchanged retention far from 1.5 grams, or Cworks' page stating a different figure.
Workshop Coffee's journal says that with the EK43's grind, which it describes as unimodal with a small standard deviation, flow rate relates more closely to the dial on the grinder. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
EK43 shots at one fixed dial setting, dose and tamp whose flow times vary widely from shot to shot.
Workshop Coffee reports grinding on the EK43 for filter strength coffee shots pulled on espresso equipment and measuring extraction yields above 22 percent. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A repeat of Workshop Coffee's filter strength shot on an EK43 grind that measures an extraction yield at or below 22 percent.
Mahlkönig's US store lists the EK43 at $3,899.00 in black or white. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The Mahlkönig US store page showing a different price for the EK43.
Niche Coffee's store lists the Niche Zero single dose grinder at $689.00 with US dollars selected. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The Niche Coffee store page showing a different US dollar price for the Niche Zero.
Hemro Group's own brands page calls Mahlkönig the first name in premium coffee grinders for baristas and coffee shops. The same page calls HeyCafé the accessible and affordable brand for coffee shop startups. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Hemro Group's brands page describes Mahlkönig or HeyCafé with different positioning words, or drops either brand from its line-up.
HeyCafé's about page says the company was founded in Shanghai in 2006, moved its factory to Changzhou in 2011, and became a wholly owned subsidiary of the Hemro Group in 2018. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
HeyCafé's about page or a Hemro Group filing gives a different founding city, factory location, or year of becoming a wholly owned subsidiary.
Mahlkönig says its Sync Scale connects to a Sync-enabled grinder for use with any espresso machine. The scale sends the measured shot time through the Mahlkönig Cloud to the grinder, which fine-tunes its burr adjustments automatically. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Sync Scale paired with a Sync-enabled Mahlkönig grinder that will not operate with an espresso machine lacking its own connectivity, or a grinder that leaves its burr setting unchanged after receiving the scale's shot time.
Daily Coffee News reported on October 30, 2025 that the Mahlkönig Sync Scale was priced at $249.99 and available in select countries, with availability planned to expand to the U.S. before the end of 2025. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Mahlkönig price list or a launch-period listing from an authorized dealer showing a launch price other than $249.99, or U.S. availability before October 30, 2025.
Kaffeemacher reports that Xenia Espresso has officially been part of the Hemro Group since May 23, 2025. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Hemro Group or Xenia Espresso statement, or a German commercial register entry, dating the change of ownership to a different day.
Mahlkönig says the E64 WS Home, launched alongside the Mahlkönig Xenia, is the first grinder to bring Grind-by-Sync to the home. Mahlkönig lists the Xenia with a dual boiler system, 3-point heating and an intake heater. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
An earlier Mahlkönig home grinder shipping with Grind-by-Sync, or a Mahlkönig Xenia specification sheet listing a single boiler.
Daily Coffee News quotes Hemro Group CEO Marcel Lehmann saying that bringing Holger Dreissig and the Xenia platform into the Mahlkönig family created a product ecosystem that delivers professional-level performance to coffee lovers at home. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The Daily Coffee News article or Mahlkönig's own launch post attributing those words to a different speaker or wording them differently.
DF64 Coffee's product page lists the DF64 Gen 2 Single Dose Coffee Grinder with 64mm stainless steel flat burrs at a regular price of $450.00 USD and a sale price of $399.00 USD. The same page says that when a buyer selects the SSP burr option, the SSP burrs are installed and aligned before shipping. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The DF64 Coffee product page for the DF64 Gen 2 shows a burr size other than 64mm, prices other than $450.00 regular and $399.00 sale, or no SSP burr option.
Niche Coffee's own product page lists the Niche Zero, a single dose grinder with 63mm conical burrs, at £559.00 on its United Kingdom storefront. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The Niche Coffee product page shows a burr size other than 63mm conical or a GBP price other than £559.00.
Barista Life's comparison of the two grinders says the DF64's 64mm flat burrs favor clarity and lighter roasts, while the Niche's 63mm conical burrs give more body. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A blind tasting of one light roast ground on a stock DF64 Gen 2 and a Niche Zero in which tasters find no difference in clarity or body between the two cups.
Complete Home Barista writes that the Niche Zero excels at medium and dark roasts, where body and chocolate notes benefit from conical burr grind profiles. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A blind tasting of one medium or dark roast ground on a Niche Zero and on a 64mm flat-burr grinder in which tasters prefer the flat-burr cup for body and chocolate notes.
Niche's own blog says the Niche Zero uses Mazzer conical burrs, a burr set it describes as typically found in larger commercial grinders. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Niche Zero burr set that carries another maker's marking, or a Niche statement naming a burr maker other than Mazzer.
Niche's Zero leaflet says the grinder is driven by a DC motor and gearbox, which it says ensure optimum burr speeds and quiet operation. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Niche Zero teardown showing an AC motor or no gearbox between motor and burrs.
Niche's product page lists the Niche Zero's noise at 72dB during grinding. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A sound meter reading of a Niche Zero grinding well above 72dB under the conditions Niche's tech spec describes.
1st-line Equipment lists the Mazzer OEM FMA00151B 83mm flat burr set at $84.95, for the 1-phase Mazzer Royal and Stark Doser grinders. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The 1st-line listing for FMA00151B showing a different price or a different burr diameter.
Niche's product page captured on 20 April 2021 listed the Niche Zero at £499.00 and told non-UK customers they may be charged VAT and duty on import at local rates, collected by the courier. The page showed one price above the UK, US and EU plug models. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The Wayback Machine capture of nichecoffee.co.uk/products/niche-zero dated 20 April 2021 showing a different price, more than one price, or no notice about VAT and duty on import.
Niche's shipping policy dated 13 January 2022 said an order may be subject to import duties and taxes including VAT once it reaches the destination country, and that Niche is not responsible for those charges. That policy said nothing about whether UK VAT was charged on orders shipped abroad. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The Wayback Machine capture of nichecoffee.co.uk/policies/shipping-policy dated 16 January 2022 carrying a sentence on UK VAT for orders shipped outside the UK.
Niche's shipping policy, last updated 22 April 2026, says orders shipped outside the UK are not charged UK VAT but may be charged local taxes and duties at the applicable rates, which the customer pays and the courier collects. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The live shipping policy at nichecoffee.co.uk no longer carrying the sentence that orders shipped outside the UK are not charged UK VAT.
Niche's calibration guide defines the Niche Zero's zero point as the position where the burrs touch. The same guide warns that grinding while the grinder is set to calibrate mode may damage the burrs. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Niche's calibration guide, read on nichecoffee.co.uk, does not define the zero point as the position where the burrs touch, or does not warn that grinding in calibrate mode may damage the burrs.
Niche Coffee's own blog says the Niche Zero uses Mazzer conical burrs, and its product page lists them as 63mm conical burrs. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Niche Zero burr set stamped by another maker, or a Niche page naming a burr maker other than Mazzer or a size other than 63mm.
Perfect Daily Grind reported on 13 September 2017 that the Niche Zero's Indiegogo campaign passed its £50,000 goal within days of launching, with early bird units at £350 against a £499 RRP. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Indiegogo's campaign page showing a goal other than £50,000, an early bird price other than £350, or the goal reached more than a few days after launch.
Coffeeblog reports that reviewer Dave Corbey measured the Niche Zero's total retention at 0.4 g to 0.7 g and its exchanged retention at a maximum of 0.3 g. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Dave Corbey's own published figures differing from 0.4 g to 0.7 g total retention or 0.3 g maximum exchanged retention.
Niche's product page for the Zero lists its burrs as 63mm conical burrs. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Niche's product page for the Zero listing a different burr size or a flat burr set.
Niche's product page says a turn of the Zero's dial switches it from grinding for espresso to grinding for filter in seconds. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Niche's product page describing the Zero as an espresso-only grinder or dropping the filter claim.
The Coffee Folk reports that Lance Hedrick's June 2022 video called the Niche Zero effectively unfit for filter coffee and inferior for lighter roasts, while doing better with medium and dark roasts with chocolatey notes. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Hedrick's video rating the Niche Zero as suited to filter coffee or light roasts as well as it is to medium and dark roasts.
LifeStyle Lab's reviewer found the Niche Zero's conical burrs produced textured chocolaty espresso but left clarity of flavours wanting, and called filter brewing on it a non-option due to the amount of fines. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
LifeStyle Lab's review describing the Niche Zero's filter grinds as low in fines or its espresso as high in clarity.
Niche's Niche Zero user manual tells the owner to fit the portafilter over the grind cup, invert the two, shake and tap the grind cup, then remove it. The manual gives this as the espresso workflow, not as a workaround. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A current Niche Zero user manual from Niche whose Using the Niche Zero steps carry no shake or tap instruction for the grind cup.
Niche's cleaning guide for the Niche Zero says to avoid putting the burrs in any contact with moisture or water, and that even tiny amounts of water can ruin grind efficiency. The guide does not name RDT or spraying beans. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Niche publication that names RDT or spraying beans and either permits or forbids it in its own words.
Niche's Niche Zero user manual says to keep the grinder dry at all times and never to immerse the burrs or burr-shaft assembly in water. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Niche Zero user manual from Niche that omits the keep-dry and burr-immersion rules or permits water on the burrs.
Niche's Niche Zero product page lists the grind speed as 1 gram per second, so an 18 gram dose takes about 18 seconds by the maker's own figure. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Niche's product page or manual stating a different grind speed, or a Niche timing that gives 18 grams in materially less than 18 seconds.
Kaffeemacher's 2025 re-measurement of the Niche Zero timed 18 grams at 13.5 seconds, after its 2020 test had timed the same dose at about 16 seconds. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Kaffeemacher's own test page giving a different time for 18 grams, or a repeat of its method on the same grinder that lands outside 13.5 to 16 seconds.
Kaffeemacher's 2025 re-measurement of the Niche Zero found 0.2 grams of temporary and 0.7 grams of permanent retention, 0.9 grams in all. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Kaffeemacher's own page reporting a different retention figure, or its method repeated on the same grinder landing far from 0.9 grams.
Niche's own blog says the retention from a Niche Zero or Niche Duo grinder could never be absolute zero, while its Niche Zero product page lists Zero retention as a feature. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Niche's blog or product page revised so that both give the same retention claim, or a Niche-published retention figure in grams.
Homegrounds' Niche Zero review lists the lack of a portafilter holder among the things it did not like, and the reviewer argues the dosing cup system is the better one. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Niche's product page or manual listing a portafilter holder or fork as part of the Niche Zero or its box contents.
Niche's Duo instruction book says the grinder is designed for use with two specialised 83mm flat burr sets, one for espresso and one for filter coffee. The same book's guarantee does not cover damage caused by unauthorised attachments, alterations, modifications or foreign objects. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Niche publication that lists a third-party burr set as fitting the Duo, or an instruction book revision whose guarantee covers burrs from other makers.
Kaffeemacher's December 2023 test found the Niche Duo's espresso clearer than the Niche Zero's, but not so much clearer that Kaffeemacher would upgrade from the Zero to the Duo for it. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Kaffeemacher retest, or another outlet's own tasting of the same two grinders, that finds no clarity gain or a large one.
Kaffeemacher's particle measurement of the Niche Duo found a relatively high proportion of fines and a rather broad main peak, and its espresso showed a slightly less pronounced body than the Niche Zero's. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A particle-size measurement of the Niche Duo's espresso burrs showing a low fines fraction and a narrow main peak.
Kaffeemacher measured the Niche Duo's retention at 1.6 grams in its December 2023 test, which it placed at the top of the field it had measured. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A repeat measurement of a Niche Duo's retention by the same method that returns a figure well above 1.6 grams.
Brew Coffee Home reported on August 18, 2023 that Niche had introduced the Niche Duo through its website, almost six years after the Niche Zero's launch. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Niche announcement dated after August 18, 2023 that presents the Duo as newly introduced, or a dated Niche page placing the launch in another year.
Lelit's MaraX PL62X page describes a double probe heat exchanger system with thermosyphon circulation, patent pending, that it says keeps the brewing temperature constant. The page offers a temperature button with Warm, Hot and Extra Hot settings. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Lelit's MaraX PL62X page no longer describes a double probe system or the three temperature settings.
Rocket Espresso's Appartamento TCA page lists the machine body as classic stainless or matt black and gives no steel check. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket's Appartamento TCA page names a steel check or a body material other than stainless or matt black.
ECM's Synchronika II page describes the machine as a dual boiler machine with a rotary pump, with a stainless steel coffee boiler of about 0.75 litres and a steam boiler of about 2 litres. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
ECM's Synchronika II page lists a vibration pump or different boiler volumes.
Lelit's MaraX PL62X page says the machine reaches the right coffee temperature in 24 minutes. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Lelit's MaraX PL62X page states a different heat-up time.
Rocket Espresso says its domestic machines are handcrafted in Milan and combine commercial-class engineering with Italian espresso culture. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso's own site stating that its domestic machines are built outside Milan or on an automated line rather than by hand.
Rocket Espresso says its R NINE ONE was developed to bring the best of its commercial machine development programme into a home machine, with pre and post infusion controlled through a pressure profiling system using five preset programmes or the manual paddle. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso's R NINE ONE page describing the machine as developed outside its commercial programme, or without a pressure profiling system.
Rocket Espresso presents the Appartamento as a compact espresso machine for small spaces, sold on its iconic circular side inserts and design character alongside professional-class components. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso's Appartamento page dropping the design language or describing the machine as a full-size unit.
Rocket Espresso's 2026 domestic catalog says the Mozzafiato comes in two versions, with an internal tank (V version) or a plumbed-in connection (R version), and lists the R at 30 kg and the V at 27 kg. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket's catalog page for the Mozzafiato describing the V and R versions as differing by something other than the water connection, or listing weights other than 30 kg for the R and 27 kg for the V.
Whole Latte Love's 2023 comparison pulled 17.3 gram shots on a Rocket Mozzafiato Evoluzione R and a Rocket Giotto Type V with the same coffee, grind size, dose and brew temperature, and reported that the rotary pump shot had richer, deeper flavor and a more favorable mouthfeel. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A repeat of Whole Latte Love's matched-shot comparison on those two machines in which the writer reports no flavor or mouthfeel difference between the rotary and vibration pump shots.
In Whole Latte Love's 2023 comparison the brew pressure gauge on the vibration pump Rocket Giotto Type V bounced between 8 and 9 bar during the shot, which the writer tied to the PID briefly energizing the heating element, while the rotary pump machine's gauge read steady. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A gauge trace from that comparison showing the vibration pump machine holding one pressure through the shot, or the rotary machine's gauge moving.
Whole Latte Love's listing for the Rocket Mozzafiato Cronometro R describes it as a heat exchange machine with a PID temperature controller, a near silent rotary pump, and a redesigned E61 group with integrated pre-infusion. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Whole Latte Love's Cronometro R listing describing the pump as anything other than a near silent rotary pump, or dropping the PID or E61 group from the description.
The Specialty Coffee Association's article Towards a New Brewing Chart describes the Coffee Brewing Control Chart as the main focus of the SCA Brewing Handbook and reports its test brews as made on a Curtis G4 commercial coffee brewer. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The same SCA article stating that the Coffee Brewing Control Chart applies to espresso, or reporting espresso brews.
Rocket's user manual says its Evoluzione R, R-CINQUANTOTTO and R 60V ranges are built with full commercial rotary pumps, and that this feature lets the user connect the machine directly to the mains water supply. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A current Rocket user manual for these ranges that lists a vibration pump or that does not permit a mains water connection.
Rocket's user manual tells owners plumbing in an Evoluzione R, R-CINQUANTOTTO or R 60V to use a certified plumber, and to limit line pressures exceeding 5 bars with a pressure-regulating valve on the water feed line. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A current Rocket user manual for the plumbed ranges that states a different line-pressure threshold or drops the pressure-regulating valve instruction.
Clive Coffee's Rocket R58 support page says the line pressure going into the machine should not exceed 30 to 45 PSI, to help prevent premature wear and potential damage to the machine. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Clive Coffee's Rocket R58 support page stating a different line-pressure limit or no limit.
Fluid-o-Tech's PO4000 rotary vane pump manual says a dirty filter or an insufficient supply of water can cause cavitation and wear of the pump's internal components. The same manual says the pump's warranty is not recognized if the pump operated dry or in cavitation. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A current Fluid-o-Tech PO4000 manual that no longer names cavitation as a cause of internal wear or no longer excludes cavitation from warranty.
Micromic lists a Fluid-O-Tech rotary pump with a hose-clamp fitting at a flow rate of 100 litres per hour, filed under professional coffee machines. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Micromic's listing for code 3FLT3001 showing a flow rate other than 100 litres per hour or a brand other than Fluid-O-Tech.
Rocket Espresso's R Nine One user manual lists the machine's pump as a permanent magnets volumetric pump. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Rocket Espresso document for the R Nine One that names a different pump type for the machine.
Rocket Espresso's R Nine One user manual lists factory Profile A as 4 bar, then 9 bar, then 5 bar, and says the profile system allows up to 5 time interval and pressure adjustments over the course of the extraction. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A copy of Rocket Espresso's R Nine One manual whose Profile A lists a different pressure sequence or a different number of allowed adjustments.
Rocket Espresso's Mozzafiato FAST page lists the R FAST version's pump as rotary with water connection or water tank, and the V FAST version's pump as vibration. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso's Mozzafiato FAST page listing a different pump type for either version.
Rocket Espresso's R58 TUNE page says Tune Technology lets the user time-control both the pre-infusion and the final stage of the extraction. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso's R58 TUNE page or manual stating that the pre-infusion or the final stage is not time-controlled.
Daily Coffee News reported in December 2017 that pressure profiling on Rocket's single-group R9 prototype is done manually by a rotating actuator at the top of the group that controls a potentiometer that runs the pump. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A Rocket Espresso document for the R Nine One describing a pressure control mechanism other than a potentiometer driven by the group actuator.
Rocket Espresso's R Nine One page says pre and post infusion are controlled through a full pressure profiling system using five preset programmes, or by manual control through the paddle system. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket's R Nine One page lists a different number of preset programmes or no manual paddle control.
Whole Latte Love's R Cinquantotto listing says the commercial check rotary pump has external pressure adjustment controls, so the owner can fine tune pump pressure while watching the pressure gauge. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
The R Cinquantotto's pump pressure is fixed at the factory with no external adjustment control.
Whole Latte Love's Appartamento TCA review says the four-setting Temperature Control Adjustment is listed by Rocket as a 0.9 to 1.2 bar boiler pressure range in 0.1 bar steps, and that its own testing measured closer to 1 bar at the lowest setting and about 1.35 bar at the highest. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
A boiler pressure measurement on an Appartamento TCA at the lowest setting reads well under 1 bar, or at the highest setting reads near 1.2 bar rather than 1.35 bar.
Rocket Espresso's Faustino page lists 50 mm flat burrs with stepless adjustment and four body colour options, Chrome, Matt Black, Appartamento Copper and Appartamento White. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso's Faustino page listing a burr size other than 50 mm or a colour list without the Appartamento Copper and Appartamento White options.
Rocket Espresso's Giannino page lists the grinder in four body colour options, Black/Chrome, Black/Wood, Chrome/Black and Chrome/Wood, and its specification table gives 55 mm flat burrs. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso's Giannino page listing a different colour set or a burr size other than 55 mm.
Seattle Coffee Gear's Faustino listing calls the grinder the perfect pair with Rocket Espresso's home machines and offers it in matching chrome, contrast black, or special edition Appartamento copper or white finishes. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Seattle Coffee Gear's Faustino listing no longer carrying the perfect-pair sentence or the matching-finish sentence.
Rocket Espresso's R Nine One page describes a fully saturated group system with digital PID temperature control and a full pressure profiling system with five preset programmes. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso's R Nine One page describing an E61 group or no pressure profiling system.
Seattle Coffee Gear's Super Fausto listing says the grinder matches the design of the smaller Fausto Touch and lists 75mm flat burrs with a red speed coating. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Seattle Coffee Gear's Super Fausto listing naming a different burr size or no longer describing the design as matching the Fausto Touch.
Coffeeness's review of the Rocket Faustino 3.1 says the Venice-based company Macap produces the grinder on behalf of Rocket. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso or Macap publishing that the Faustino 3.1 is manufactured by Rocket itself or by a company other than Macap.
Whole Latte Love's listing for the Rocket Macinatore Fausto describes it as a Rocket branded Eureka grinder with 65 mm burrs. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso or Eureka publishing that the Fausto is manufactured by Rocket itself or by a company other than Eureka, or a Rocket spec sheet giving a burr diameter other than 65 mm.
Rocket Espresso's Stelvio page lists 68 mm flat burrs on the Stelvio and 83 mm flat burrs on the Stelvio Elite, and calls it the tallest and most powerful grinder in its lineup. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso's Stelvio page or spec sheet giving a burr diameter other than 68 mm for the Stelvio or 83 mm for the Stelvio Elite.
Majesty Coffee lists the Rocket Espresso Faustino grinder at $850.00, with 50mm flat steel burrs and a 1.5 lb hopper. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Majesty Coffee's Faustino page shows a price other than $850.00, or a burr size or hopper capacity other than 50mm and 1.5 lbs.
Whole Latte Love lists the Rocket Espresso Faustino grinder in matte black at a regular price of $800.00. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Whole Latte Love's matte black Faustino page shows a regular price other than $800.00.
DF64 Coffee's own store lists the DF64 Gen 2 single dose grinder at a regular price of $450.00 and a sale price of $399.00. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
DF64 Coffee's DF64 Gen 2 page shows a regular price other than $450.00 or a sale price other than $399.00.
DF64 Coffee says the DF64 Gen 2's bellow hopper holds 50 grams. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
DF64 Coffee's DF64 Gen 2 page states a bellow hopper capacity other than 50 grams.
Sigma Coffee UK lists the SSP High Uniformity 64mm Red Speed flat burrs at £189.00 and says the set fits the Turin / DF64 Gen 1 and Gen 2. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Sigma Coffee UK's page shows a price other than £189.00 or drops the Turin / DF64 Gen 2 from its fit list.
Rocket Espresso's Gravo page lists 63 mm screwless burrs, a 300 g hopper, time dosing and grind by weight. source
Checked by Product.ai on 2026-10-19
What would prove this wrong
Rocket Espresso's Gravo page drops grind by weight, time dosing, the 300 g hopper or the 63 mm screwless burrs.